Trusted & Accredited By
Accredited Test
| Material / Products | Type of Test | Test Method |
|---|---|---|
| Hardened Concrete | Compressive Strength of Cube & Cylinder | BS EN 12390-3: 2009 MS EN 12390-3: 2012 |
| Compressive Strength of Core | BS EN 12504-1: 2019 MS EN 12504-1: 2013 |
|
| Density | BS EN 12390-7: 2019 | |
| Density, Absorption and Voids | ASTM C 642: 21 | |
| Initial Surface Absorption | BS 1881 Part 208: 1996 | |
| Water Absorption | BS 1881 Part 122: 2011+A1: 2020 | |
| Water Permeability | BS EN 12390-8: 2019 DIN 1048 Part 5: June 1991 |
|
| Rapid Chloride Permeability | AASHTO Designation T277:22 ASTM C1202-22e1 |
|
| Drying Shrinkage | MS EN 1367-4: 2012 BS 1881 Part 5: 1970 Amd. 1990 BS ISO 1920-8: 2009 |
|
| Static Modulus | ISO 1920 Part 10: 2010 BS 1881 Part 121: 1983 |
|
| Flexural Strength | BS EN 12390-5: 2019 | |
| Tensile Splitting Strength | BS EN 12390-6: 2009 | |
| Creep in Compression | ASTM C512/C512M-15 ISO 1920-9: 2009 (E) |
|
| Windsor Probe | ASTM C803/C803M-18 | |
| Rebound Hammer | BS EN 12504-2: 2021 | |
| Fresh Concrete | Air Content | BS EN 12350-7: 2019 |
| Bleeding | ASTM C232/C232M – 21 | |
| Setting Time | ASTM C403/C403M – 23 | |
| Metallic Fiber Concrete | Flexural Strength | ASTM C1609/C1609M – 19a BS EN 14488-3: 2006 BS EN 14651: 2005 (Amd.2007) EFNARC: 1996, Clause 10.3 JSCE-SF4: 1984 |
| Toughness Strength | BS EN 14488-5: 2006 EFNARC: 1996 |
|
| Mortars | Compressive Strength | ASTM C109/C109M-21 ASTM C579-23 BS 6319: Part 2: 1983 BS 4551: 1980 BS EN 1015-11: 2019 BS EN 196-1: 2016 BS EN 12190: 1999 MS 522 Part 2: 2005 |
| Portland Cement | Autoclave Expansion | ASTM C151/C151M – 18 |
| Grout for Prestressing Tendons | Compressive Strength | BS EN 445: 2007 |
| Epoxy Bonding Agent | Compressive Strength | FIP/9/2: 1978 ASTM D695-15 |
| Bitumen | Thickness or Height of Compacted | ASTM D3549/D3549M-18 |
| Bulk Specific Gravity and Density | ASTM D2726/D2726M-21 | |
| Bitumen Content | ASTM D2172/D2172M-17e1 | |
| Marshall Stability and Flow | ASTM D6927: 22 | |
| Aggregates | Sieve Analysis | BS EN 933-1: 2012 MS 30: Part 4, 1995 |
| Particle Density and Water Absorption | BS 812: Part 2: 1995 MS 30: 1971 BS EN 1097-6: 2022 |
|
| Flakiness Index | BS 812: Part 105-1: 1989 MS 30: Part 5, 1995 BS EN 933-3: 2012 |
|
| Elongation Index | BS 812: Part 105-2: 1990 MS 30: Part 5, 1995 BS EN 933-4: 2008 |
|
| Aggregate Crushing Value (ACV) | BS 812: Part 110: 1990 MS 30: Part 8, 1995 |
|
| Aggregate Impact Value (AIV) | BS 812: Part 112: 1990 MS 30: Part 10, 1995 |
|
| Ten Percent Fines Value (TFV) | BS 812: Part 111: 1990 MS 30: Part 9, 1995 |
|
| Clay, Silt and Dust | BS 812: Part 1: 1975 MS 30: 1971 Section 3 ASTM C117 – 17 |
|
| Clay Lumps | ASTM C142/C142M – 17 | |
| Los Angeles Abrasion Test (LA) | ASTM C131/C131M – 20 MS 30: Part 11, 1995 ASTM C 535 – 16 BS EN 1097-2: 2020 |
|
| Bulk Density, Voids and Bulking | BS 812: Part 2: 1995 | |
| Loose Bulk Density and Void | BS EN 1097-3: 1998 | |
| Organic Impurities | ASTM C40/C40M – 20 MS 30: Part 15: 1995 |
|
| Soundness (Sodium Sulfate / Magnesium Sulfate) | ASTM C 88/C88M – 18 AASHTO Designation: T104-22 |
|
| Lightweight | ASTM C123/C123M – 14 | |
| Shell Content | BS 812: Part 106: 1985 MS 30: Part 6, 1995 BS EN 933-7: 1998 |
|
| Sand Equivalent | ASTM D 2419 – 22 BS EN 933-8: 2015 |
|
| Potential Alkali (Mortar-Bar) | ASTM C 1260 – 22 | |
| Polished Stone Value | BS EN 1097-8: 2020 | |
| pH Value | BS 1377: Part 3: 2018+A1: 2021 | |
| Methylene Blue | BS EN 933-9: 2022 | |
| Soil | Particle Size Distribution | BS 1377-2: 2022 BS EN ISO 17892-4: 2016 |
| Liquid Limit (Fall Cone Method) Liquid Limit (Casagrande Method) Plastic Limit & Plasticity Index |
BS 1377-2: 2022 BS EN ISO 17892-12: 2018 |
|
| Bulk Density | BS 1377-2: 2022 BS EN ISO 17892-2: 2014 |
|
| Water Content | BS 1377-2: 2022 BS EN ISO 17892-1: 2014 |
|
| Compaction (Rammer Method) Compaction (Vibrating Hammer) |
BS 1377-2: 2022 | |
| Laboratory CBR | BS 1377-2: 2022 | |
| In-Situ CBR | BS 1377: Part 9: 1990 | |
| Mackintosh | In-house Method (JKR Spec.) | |
| Field Density | BS 1377: Part 9: 1990 ASTM D1556-15e1 |
|
| Steel | Tensile | ASTM A370-21 BS EN ISO 15630-1: 2019 ISO 15630-1: 2019 ISO 6892-1: 2019 MS 144: 2006 MS 144: 2014 MS 146: 2006 MS 146: 2014 |
| Bending | ASTM A370-21 BS EN ISO 15630-1: 2019 BS EN ISO 7438: 2020 ISO 15630-1: 2019 ISO 7438: 2020 MS 146: 2006 |
|
| Rebend | BS EN ISO 15630-1: 2019 ISO 15630-1: 2019 MS 144: 2006 MS 144: 2014 MS 146: 2006 MS 146: 2014 |
|
| Multi Wire Steel Strand | Tensile & Elongation | ASTM A1061/A1061M-20ae1 ASTM A370-21 BS 5896: 2012 BS EN ISO 15630-3: 2019 |
| Ground Anchorages | Pull Out Load | BS 8081: 2015 |
| Structural Fixings | Pull Out Test | BS 5080-1: 1993 BS 8539: 2012 |
| High Tensile Wire and Strand | Stress Relaxation Test | ASTM A1061/A1061M-20ae1 ISO 15630-3: 2019 MS ISO 15630-3: 2009 |
| Mechanical Coupler | Tensile Test | ISO 6892-1: 2019 Specification refer to BS 8110: Part 1: 1997 (Amd. 1998) |
| Threaded Fastener | Nut: Cone Proof Load Test Proof Load Test |
ASTM F606/F606M-21 ISO 898-2: 2022 BS EN ISO 898-2: 2022 |
| Bolt & Stud: Tensile Under Wedge Loading Tensile Tensile and Elongation Proof Load Test |
BS EN ISO 898-1: 2013 ISO 898-1: 2013 |
|
| Ceramic Tiles | Water Absorption | MS ISO 10545-3: 2001 |
| Modulus of Rupture | MS ISO 10545-4: 2003 | |
| Chemical Resistance | MS ISO 10545-13: 2001 | |
| Resistance to Stains | MS ISO 10545-14: 2001 | |
| Bricks and Blocks | Compressive Strength | BS EN 772-1:2011+A1: 2015 MS 1933-1: 2017 |
| Water Absorption | EN 772-7: 1998 MS 1933-7: 2017 |
|
| Vitreous China Sanitary Appliances | Water Absorption Chemical Resistance Resistance to Staining |
MS 147: 2021 |
| Security Seals | a) Tensile b) Shear c) Bend |
ISO 17712: 2013(E) |
| Rock | Point Load Strength Index | ASTM D5731-16 |
| Geotextile | Trapezoid Tearing Strength | ASTM D4533/D4533M-15 |
| Tensile Properties | ASTM D4595/D4595M-23 | |
| Grab Breaking Load and Elongation | ASTM D4632/D4632M-15a | |
| Index Puncture Resistance | ASTM D4833-2020 | |
| Rubber & Plastic | Tensile and Elongation | ASTM D412-16 (2021) ASTM D638-22 |
| Compressive Strength | ASTM D695-23 | |
| Thermal Insulating Product – Polystyrene Foam | Compressive Strength | BS EN 826: 2013 |
| Rigid Cellular Materials | Compressive Strength | ASTM D1621-16 |
| Products and Systems for Protection and Repair Products for Concrete Structure | Pull Off Test | BS EN 1542: 1999 |
| Coating Materials | Pull Off Strength | ASTM D4541-22 |
Non-Accredited Test
Hardened Concrete Test
- Ultrasonic Pulse Velocity Test
- Concrete Strength – MG4
- Half Cell Potential Test
- In-situ Carbonation Test
- Covermeter Test to check
i) Concrete cover
ii) Rebar Spacing
iii) Rebar locatopm
iv) Rebar size - Impact Echo Test to check
i) Concrete Thickness
ii) Intergrity & delamination condition - Pull Out Test
- In-situ Load Test
- Visual Inspection and mapping
- Crack Survey and mapping
- Monitoring crack using Demec Gauge
- Check Crack Depth using UPV
- Chloride & Sulphate Content
- Cement Content
- Cement Aggregate Content
- Original Water Content
- Concrete Petrographic Examination
- Accelerated Chloride Penetration
- Restrained Expansion
- Concrete Temperature Monitoring
- Electrical Resistivity Test
- Chloride Diffusion Coefficient Test
- Sorptivity Test
- Chloride Uptake Test
- Chemical Resistance Test
- Chemical Analysis Test
Fresh Concrete Test
- Air contest
- Slump test
- Concrete Setting Time
- Bleeding and Expansion Test
- Wick-Induced Test (Volume Change and Bleeding)
- Viscosity of clay construction slurries
(Marsh Funnel Method) - Flow Table Test
- Flow Through Test
- Flow Ability Test by Flow Cone Method
- Fluidity Test (Cone Method)
- Fluidity Test (Grout Spread Method)
- Melt Mass Flow Rate (MFR) Test
Concrete Admixture Acceptance Test
- Trial mix for control and test mix
- Slump Test
- Air Content Test
- Stiffening Times Test
- Setting Time
- Water reduction
- Compressive Strength
- Length Change Test
Rock
- Unconfined Compressive Strength
- Wet/Dry Compressive Strength Test
- Young Modulus & Poisson’s Ration Test
- Elastic Modulus Test
- Bulk Modulus Test
- Direct Shear Strength Test
- Direct Tensile Test
Concrete Admixture Test
- Color – Visual Test
- Homogeneity -Visual Test
- Effectiveness component
- Specific Gravity or Relative Density
- Dry Material Content
- pH Value Test
- Sulfate Content
- Chloride Ion Content
- Alkali Content / Total Na2O Equivalent
Expension Agent
- Fineness (Blaine method)
- Fineness (1.18mm sieve)
- Initial and Final Setting Times
- Compressive Strength
- Restrained Expansion Rate
- Magnesium Oxide
- Alkali Content
- Sulfate Content
- Chloride Content
Cement Test
Physical Test
- Compressive Strength Test
- Specific Surface (Blaine Air method)
- Initial and Final Setting Times
- Soundness (Le Chatelier method)
- Fineness Test (Blane Method )
- Normal Consistency
- Heat of Hydration
Chemical Analysis
- Insoluble Residue (IR)
- Loss On Ignition (Lol)
- Chloride Content (Cl)
- Sulphatte Content (SO3)
- Calcium Oxide (CaO)
- Silicone Dioxide (SiO2)
- Magnesium Oxide (MgO)
- Total Alkali Content (Na2O)
- Iron III Oxide (Fe2O3)
- Free Calcium Oxide Content (CaO)
- Tricalcium Aluminate (C3A)
Silica Fume
Physical Test
- Density
- Bulk Density
- Oversize Amount Retained when wet-sieved on a 45mm sieve
- Specific Surface Area by Gas Absorption (BET Method)
- Accelerated Possolanic Strength Activity Index with portland cement.
- Dry Mass Content
- Fineness
- Activity Index Test
Chemical Analysis
- Loss on Ignition (Lol)
- Silicone Dioxide, SiO2
- Moisture Content
- Sulphatte Content (SO3)
- Na2O Equivalent
- Analysis of Free Calcium Oxide
- Elemental Silicon, (Si)
Pulverized Fly Ash (PFA)
Physical Test
- Fineness , residue below 45µm test sieve
- Fineness Test (Blaine Air Method)
- Soundness (Le Chatelier Method)
- Density (Le Chaterlier Flask Method)
- Initial & Final Setting Times
- Activity Index test
- Water requirement
Chemical Analysis
- Loss On Ignition (Lol)
SiO2 + Fe2O3 + Al2O3 - Sulphate Content (SO3)
- Chloride Content (CI)
- Silicone Dioxide (SiO2)
- Calcium Oxide (CaO)
- Magnesium Oxide (MgO)
- Phosphate (P2O5)
- Total Alkali Content
- pH Value
- X-Ray Fluorescence (XRF)
Fe2O3, CaO, SIO2, Al2O3, MgO, Cr2O3
Aggregate
- Micro Deval Test
- Wet /Dry Attrition Value Test
- Petrographnic Examination test
- Fine Aggregate Angularity Test
- Fracture Face Test
- Shape Test
- Potential Alkali Reactivity (Chemical Method)
- Chloride Content
- Sulphate Content
- Sulfur Content
- Flow coefficient of aggregate as per EN 933-6: 2022
- Cantabro Test
Bricks / Blocks
- Compressive Strength
- Thermal Conductivity of Insulating
- Abrasion Resistance
- Drying Shrinkage
- Fluorescence
- Water Absorption
Geotextiles Test
- In-Plane Flow Rate per unit Width
- Apparent Opening Size
- Nominal Thickness & Width
- Tensile Properties of Non-reinforcement
- Proof Tension Force
Pain / Varnishes Test
- Non-Volatile Matter of Points
- Resistance to Continuous Salt Spray
- Through-Dry State & Through Dry Time
- Paints & Varnishes – Bend Test
- Resistance to Liquid
- Volatile Organic Compound
- Viscosity (Rotary Viscometer)
- Water Content
Fiberglass Mesh
- Physical Properties
- Glass Fiber Content
Rubber / Plastic Test
- Durometer Hardness
- Linear Coefficient
- Lumber & Plastic Shape
- Indentation Hardness
- Unrestrained Volumetric Expansion
- Barcol Hardness
- Evaluating the Resistance
- Impact Resistance
- Thickness
- Compression Stress & Stress-Strain
- Characteristic for Flexible
- Ring Stiffness & Assessment
- Density
- Strength of Adhesively Bonded
- Evaluation of PVC Waterstop
- Water Absorption
- Conical Base Rubber Solid Tyres
- Tensile Properties
Coatings
- Thermal Conductivity
- Volatile Organic Compound Content
- Slip / Skip Resistance Measurement
- Pedestrian Surface Materials
- Salt spray Corrosion Test
- Artificial Atmosphere
- Impact Resistance of Coating
- Density
- High Temperature Service Evaluation
- Cathodic Disbondment Test of Pipeline
- Performance of Bitumen-Based
- Abrasion Resistance
- Pull off Strength
- Bonding Strength
Aggregate Test
- Durability Index
- Abrasion Value
- Moisture Content
- Chloride and Sulphate Content
- Flat & Elongated Particles
- Fracture Face
- Micro Deval
- Scratch Hardness
- Texture Depth
- Total Evaporable Moisture Content
- Fineness Modulus
- Particle Density
- Degradation Factor in Fine Aggregate
- Coefficient of Uniformity
- Chemical Analysis
- Wet / Dry Attrition
- Void Ratio on Compacted
- Percussion Rig Boring Surface
Epoxy Resin Test
- Bonding Strength
- Gel-Time & Peak Exothermic Temperature
- Sag Flow of Highly Viscous Resin
- Viscosity
- Water absorption & Solvability in water
- Consistency
- Open Time
- Temperature Deflection
- Modulus of Rupture (MOR)
- Slant Shear Strength
- Softening Point Resin
Garnet
- Particle size Distribution
- Water Solubility
- Moisture Content
- Apparent Porosity
- Assessment of Hardness
- Water soluble Contaminants
- Water Soluble Chloride Content
Ceramic Tiles
- Crazing Resistance
- Dimension and Thickness
- Moisture Expansion
- Rectangularity
- Resistance to Deep Abrasion
- Resistance to Surface Abrasion
- Straightness of Sides
- Surface Flatness (Curvature & Warpage)
- Adhesive Strength
Steel Test
- Mass of Zinc Coating
- Mass of Rust
- Cross Section Area & Diameter
- Measuring of Rebar Diameter
- Measuring of Dimension
- Proof Load
- Chemical Analysis
- Modulus of Elasticity
- Compression Shear
- Tensile Pulling Test
- Mechanical Test for Port Tensioning Wedges
- Tensile Test for Mechanical Splices
- Bend Testing for Metallic Flat Materials for Spring
- Applications
- Chemical Composition of Steel Bar
- Wet Heat Aging Resistance (Tensile Test)
- Magnetic Particle of Welds
- Destructive Test on Welds in Metallic
Materials - (Fracture Test)
- Proof Test of Carbon Steel Chain
- Bending Yield Moment
- Decrepitation Index
- Tensile Force for Welded Steel Article
- Adhesion Strength
- Pull Off Test
- Salt Spray Corrosion
Soil and Foundation Test
Soil Laboratory
- Electrical Resistivity
- Falling Head Permeability Test
- Mass Loss on Ignition
- Mica Content
- Organic Matter Content
- Particle Density of Soil
- Redox Potential
- Small / Large Shear Box
- Soil Chemical Test
- Thermal Conductivity
- Volumetric Shrinkage for Soil
- Heavy Metal in Soil or Sand by Portable X-Ray
Fluorescence - Chemical Analysis
In-Situ Testing
- Dynamic Cone Penetrometer
- Plate Bearing Test
- Seepage Rate
- Proof Rolling Test
- Water Content
Fly Ash
- Compressive Strength
- Moisture Content
- Activity Index
- Chemical Analysis
- Water Requirement
- Loss on Ignition